Plumbing Basics: The First Step for Bathtub Installation
Plumbing Basics: The First Step for Bathtub Installation
Blog Article
Were you trying to locate help and advice concerning Installing A Bathtub?
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
Setting up a bathtub isn't specifically rocket science, however it does need strong plumbing, carpentry, and also occasionally, tiling abilities. Changing an old bath tub with a brand-new one is also a reasonably difficult task. If the old bathtub is readily accessible, the task can move speedily; if you have to open a wall to get rid of the old bathtub as well as position the brand-new bath tub, the task is much harder. In either instance, the job is within a home handyman's abilities, although you will certainly need an assistant to leave the old bathtub and also embeded in the new one. See to it you have certified yourself for the work as well as fit attempting it. Rather than employing a professional to take control of a halfway-completed project, it is far better to consider utilizing one prior to you begin. Chances are you might require a professional plumber to make tube connections.
This post will certainly aid you install a new bath tub in your washroom if you have actually already acquired a brand-new tub and also do not require to transform the plan of your previous water system pipes.
Your tools and product list need to consist of the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your installment, then the first thing you need to do is disconnect the water supply. After doing so, switch on the faucets to drain any type of water continuing to be in the system. The process of eliminating the existing faucets can be quite troublesome as a result of the restricted gain access to that is frequently the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the taps. Have a fabric prepared for the staying water that will come from the pipes. When the supply pipes have been eliminated, utilize the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the single taps from turning throughout this process. When the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any type of old securing compound.
Before proceeding to fit the brand-new faucets, compare the pipeline connections on the old taps to the new faucets. If the old taps are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic adapter to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will call for reducing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the tap in the mounting opening in the bath/basin making sure that the washers remain in location in between the tap as well as the sink. Protect the tap in place with the manufacturer offered backnut. As soon as the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular tap ports. The previous type must be connected to the tap ends initially, tightening up just by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.
Mounting the Tub
Making use of the two wood boards under its feet, place the tub in the required placement. The wooden boards are valuable in evenly spreading out the weight of the bathtub over the area of the boards rather than focusing all the weight onto 4 tiny factors.
The following objective is to make certain that the bathtub is leveled all round. This can be accomplished by checking the spirit level and readjusting the feet on the bath tub until the spirit level reviews degree.
To mount faucets, fit all-time low of the outermost versatile tap port to the appropriate supply pipeline by making a compression join; after that do the same for the other faucet.
Switch on the water as well as examine all joints and new pipework for leakages and tighten them if required. Fill the bathtub as well as additionally check the overflow outlet and the normal outlet for leaks.
Lastly, fix the bath paneling as defined in the producer's instruction manual. Tiling as well as sealing around the tub ought to wait till the bathtub has actually been made use of a minimum of once as this will certainly settle it right into its final setting.
Preparing for the Setup
To start with, the supporting structure supplied with the bath should be fitted (if needed) according to the supplier's instructions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is very important to see to it that if the tap comes with a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps unit to stop stress on the bath tub.
Fit the versatile faucet adapters to the bottom of both taps utilizing 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of every one of the provided washers.
Connect the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath should now prepare to be suited its last setting.
Tiling Around the Bath tub
In the area where the bathroom fulfills the tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to break a stiff seal, causing the water to pass through the wall surface between the bath as well as the tiling, leading to complications with moisture and also possible leaks to the ceiling listed below.
You can pick from a range of coloured sealers to blend in your fixtures and also installations. They are marketed in tubes and also cartridges, and also can sealing gaps as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly fill the bathtub with water before sealing, to enable the activity experienced when the tub remains in use. The sealant can split relatively very early if you do not consider this motion prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise easily offered on the market. It is a good idea to fit the ceramic tiles using water-resistant or water resistant adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you liked our article on A Step-by-Step Guide to Installing a Bathtub. Thanks so much for taking time to read our piece of content. Sharing is good. One never knows, you might be helping someone out. We treasure reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Excellence awaits, dial! Report this page